Home > Adhesive Base Stick Mounts > RAP-SB-178 (.75 Inch Snap Link Ball and Socket Arm) Assemblies with Cradle > Apple Assemblies >

Universal 2.5 Inch Adhesive Flex Stick Base with RAM-HOL-AP9U Apple iPhone 4 Holder (4th Gen/4S WITHOUT Case or Cover)
Universal 2.5 Inch Adhesive Flex Stick Base with RAM-HOL-AP9U Apple iPhone 4 Holder (4th Gen/4S WITHOUT Case or Cover)
 
Price $25.49

STOCK STATUS: In Stock - Ships Next Bus. Day

Free Shipping
Product Code: RAP-SB-178-AP9U
QTY:

DESCRIPTION
 
The RAP-SB-178-AP9U with snap link ball mount and flexible base installs in seconds to any flat surface. Just peal off the protective vinyl patch on the flex base and stick it where you want your electronic device secured. This mount is designed for the following models:
  • Apple iPhone 4
NOTE: This cradle WILL NOT FIT the 1st generation or earlier iPhone models. To see all iPhone cradles click here.

RAP-SB-178-AP9U shown above.

RAP-SB-178-AP9U Includes the Following:
  • Warranty: Manufacturer's, RAM Mounts (National Products Inc.), Limited Life Time Warranty.
  • Base: The base includes a 2.5 inch RAM-202PSA 3M semi-permanent adhesive disk pad that attaches firmly to a flat surface. 
  • Arm: Flexible snap link arm that allows the ultimate in versatility.
  • Adapter: Composite black powder coated universal diamond plate. Two holes measuring 1.9 inches from center to center is compatible with the AMPS hole pattern and any RAM Mount holder.
  • Cradle: The RAM-HOL-AP9U high strength plastic cradle is design to hold the models specified above. The cradle has a cut away at the bottom to allow the connection of all required cables (Not Included). The cradle also enables full access to the volume and mute button on the side along with the power button and headphones jack at the top of the iPhone. 
NOTE: To find other Apple, cell phone or GPS holders click here.
Instructions
  • General recommendations to properly adhere the adhesive disc.
    1. Ensure that both the dashboard surface and the bottom of the Ram Mount base have been thoroughly cleaned and dried.
    2. Attach either side of adhesive to the base first, let it sit several hours to allow adhesive to thoroughly bond.
    3. Attach other side of adhesive (with base) to the dashboard surface.
    4. Let the adhesive disc sit several hours before adding socket arm components, etc. to allow the adhesive to properly bond to the dashboard surface.

ACCESSORIES FOR THIS PRODUCT...
Apple iPod Nano RAM-HOL-AP5U Cradle for iPod Nano (3rd Generation WITHOUT Case or Cover) Universal Small Sized Electronic Device Holder (Fits Device Width 1.5" to 2.5") Universal Finger Gripping Cradle (Fits Device Width 1.25" to 3.5" Including GPS, eTrex, 2 Way Radios, Smartphones with Cover/Case iPhone, Droid, etc.) Apple iPhone RAM-HOL-AP3U Cradle for 1st Generation (Non 3G) WITHOUT Case or Cover
Price $13.49

Add Free Shipping
Price $24.49

Add Free Shipping
Price $34.99

Add Free Shipping
Price $10.99

Add Free Shipping
Apple iPod Nano RAM-HOL-AP5U Cradle for iPod Nano (3rd Generation WITHOUT Case or Cover) Universal Small Sized Electronic Device Holder (Fits Device Width 1.5" to 2.5") Universal Finger Gripping Cradle (Fits Device Width 1.25" to 3.5" Including GPS, eTrex, 2 Way Radios, Smartphones with Cover/Case iPhone, Droid, etc.) Apple iPhone RAM-HOL-AP3U Cradle for 1st Generation (Non 3G) WITHOUT Case or Cover


Browse for more products in the same category as this item:

Adhesive Base Stick Mounts > RAP-SB-178 (.75 Inch Snap Link Ball and Socket Arm) Assemblies with Cradle > Apple Assemblies
iPhone Adhesive Base Assemblies