RAM-TRIPOD1-234-3 Tripod Mount with Tough Tray, Camera Adapter & Case

Description

RAM-TRIPOD1-234-3 shown above (computer not included).

RAM-TRIPOD1-234-3 Includes the Following:

Warranty: Manufacturer's, RAM Mounts (National Products Inc.), Limited Life Time Warranty.
Bubble Level: Built in bubble level and comfortable grips make setup and handling a breeze.
Carrying Case: A carrying case with strap is included to house the RAM-TRIPOD1.
Dimensions: Three piece telescoping legs with quick release allow the legs to be independently adjusted for uneven surfaces. The tripod adjusts to following heights:

Minimum Tripod Height: 21 inches (without Tough Tray)
Maximum Tripod Height: 58 inches (without Tough Tray)

Hardware Included: Yes. Dual sided threaded screw with 3/8"-16 male and 1/4"-20 male thread attaches to the tripod center column. This can be used to secure cameras and other accessories.
RAM-202CNSU: Single 2.5 inch diameter mount with 3/8"-16 female hole and 1.5 inch diameter rubber ball. This mount attaches to the supplied 3/8"-16 male thread on top of the RAM-TRIPOD-1.

RAM-201U: Double socket arm allows a 1.5 inch diameter ball accessory to be connected at either end. A tightening knob on the side of the arm enables the sockets to clamp firmly to the attached accessories. The arm allows for easy adjustment by loosening the side knob, a single spring inside the arm opens the sockets, allowing the arm to pivot on the attached accessory. This enables the arm and accessories to be positioned at various angles allowing the ultimate in position flexibility. Loosen the knob completely and the arm will disconnect from the accessories in seconds!

Arm Material: Black powder coated marine grade aluminum with plastic twist knob.
Arm Length Socket Center to Socket Center: 4.55 inches.
Overall Arm Length: 5.625 inches.

RAM-202U: 2.5 inch diameter marine grade aluminum mounting plate with 1.5 inch diameter rubber ball. The plate has pre-drilled holes included the AMPS hole pattern. This mounting plate can be used to attach to RAM Tough Tray and RAM electronic holders (RAM-HOL-xxxx)

Tough Tray Description: The RAM-234-3 "Tough-Tray" will hold laptops with a width from 10 to 16 inches and also works with most 17 inch screen laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics.
Tough Tray Dimensions: The device dimensions the RAM-234-3 Tough Tray will accommodate are listed below:

Tray Depth: 10.0 inches
Tray Thickness: 2.125 inches
Tray Width (Expansion): 10 inches to 16 inches NOTE: Works with 17 inch screens
Side Clamp Arm Height: 0.5 inch (min) to 1.75 inches (max)

NOTE: To compare dimensions of the original Tough Tray and Tough Tray II click here.

NOTE: Please see the RAM Tough Tray 2 (RAM-234-6) for smaller electronic devices such as netbooks.

RAM-TRIPOD1-234-3 Options (NOT INCLUDED):

Power Caddy: RAM-234-5U attaches to the back of the Tough Tray II and holds power supplies and small accessories.
Screen Support: RAM-234-S2U attaches to the side of the Tough Tray II and secures the laptop lid in a fixed position.
Tray Lock: RAM-234-LK2U locks the electronic device into the Tough Tray II.
Tripod Accessories: To view additional tripod accessories click here.

Tough Tray II vs Original Tough Tray

Tough Tray II vs Tough Tray Size Comparison shown below:

Tripod Workstation with Tough Tray RAM-234-3 Med. to Large Sized Holder

Tripod Workstation with Tough Tray RAM-234-3 Med. to Large Sized Holder